BCMaterials Fortnightly Seminar #46

MIKEL MÚGICA
(BCMaterials)
ANALYSIS OF THE FATIGUE CYCLING ON ELASTOMERIC POLYMER WITH FERROMAGNETIC PARTICLES COMPOSITES FOR DAMPING APPLICATIONS
The aim of this project is to determine the life cycle of a composite made up of a polymer matix and Ni-Mn-Ga spherical particles as the filler. NI-Mn-Ga is a Ferromagnetic Shape Memory Alloy (FSMA) that can dissipate large quantities of mechanical energy through the recoverable motion of twin boundaries. The work performed for this tesis starts with the sample manufacturing, which is done under a magnetic field to orient the particles in the composite. The samples were the characterized by thermal and magnetic analysis of the obtained composite as well as through microscopy. The information obtained from the specific instrumentation is analyzed to determine the initial properties of the Ni-Mn-Ga/PU composite. By applying a cyclic stress with the Dynamic Mechanical Analysis (DMA) and later analysis of the composite following the same procedure as for the original samples, the intention is to determine and understand the mechanisms resposible for the fatigue of the composite. Once the composite sampleshave been analyzed before and after DMA, the results are contrasted, extracting as the main conclusion that the failure of the composites is the formation of cracks in the polymeric matrix, occuring earlier if the cyclic stress is applied perpendicularly to the preferential direction of the composite than if it is applied parallell.MARI PAZ CRESPO
(BCMaterials)
APPLICATIONS OF SHAPE MEMORY POLYMERS TO SELF-HEALING SURFACES
Shape memory effect of a commercial polyolefin, polycyclooctene (PCO), crosslinked in several ways has been studied. First, PCO has been crosslinked using a monofunctional peroxide, dicumyl peroxide, or irradiated with γ-rays. Moreover, two different ionomers (Surlyn 1705 and Surlyn 8940), PCO and ionomers blends and, finally PCO and ionomers blends crosslinked with dicumyl peroxide were also studied. All samples were prepared by compression moulding and then, thermal and mechanical properties were analysed by Differential Scanning Calorimetry (DSC), Thermogravimetric Analysis (TGA) and Dynamic Mechanical Thermal Analysis (DMTA). Shape memory effect was studied by Thermo-mechanical Analysis (TMA). Finally, self-healing properties have been studied marking the sheet surfaces with a hardness test pencil in lines and holes. Scratches depths and diameters have been measured by different techniques as profilometry, confocal and optical microscopy. To conclude the project, the thermal-induced self-repair behaviour was followed in situ by optical microscopy. The aim of this project is to obtain shape memory polymers with self-healing properties to appliance applications.
Related news
Eric Hill, Ikerbasque Research Associate Professor berria
Atsegin handiz ongietorria egiten diogu Eric H. Hill Ikerbasque Research Associate Professore-ri BCMaterials-en. Hill Kimikan lizentziatu zen Oregon Hegoaldeko Unibertsitatean 2009an, eta doktoretza…Doktoratu ondoko hiru ikertzaile berri BCMaterials-en
Ongietorri beroa egiten diegu Paola Zimmermann Crocomo, Diana Cabrosi eta Francisco Peraltari, BCMaterials-en doktoratu ondoko ikertzaile gisa sartu baitziren, Eusko Jaurlaritzaren IKUR programa…Raynald Gauvinekin hitzaldi gonbidatua (uztailak 16)
Datorren uztailaren 16an, 11:00etatik aurrera, Martina Casiano eraikineko auditorioan (BCMaterialsen egoitza), Kanadako McGIll Unibertsitateko Meatzaritza eta Materialen Ingeniaritza Saileko Raynald…BCMaterials-eko puntu kuantikoei eskainitako astea
Ekainaren 30etik uztailaren 2ra, BCMaterialsek "Track the Twin" MSCA doktorego-sarearen bigarren workshopa hartu zuen, eta gure zentroa sare horren parte da. Europako proiektu honen helburua da puntu…